How to Set up a Tub Yourself
How to Set up a Tub Yourself
Blog Article
Just how do you really feel with regards to How to Install a Bathtub?
Installing a tub isn't exactly rocket science, yet it does require strong plumbing, woodworking, and often, tiling skills. Replacing an old tub with a brand-new one is likewise a reasonably difficult job. If the old bathtub is readily available, the task can relocate speedily; if you have to open up a wall surface to remove the old bathtub and also position the brand-new bath tub, the task is much harder. In either situation, the task is within a residence handyman's abilities, although you will certainly require an assistant to leave the old tub and set in the brand-new one. See to it you have actually qualified yourself for the job and also fit attempting it. Rather than working with a specialist to take over a halfway-completed project, it is far better to think about employing one prior to you begin. Opportunities are you may need an expert plumber to make tube connections.
This article will certainly assist you set up a new bath tub in your shower room if you have already acquired a brand-new tub and do not need to alter the plan of your previous supply of water pipes.
Your devices and also product checklist ought to comprise the following:
Removing Old Touches
If you require to change old faucets with new ones as a part of your setup, then the first thing you should do is disconnect the water supply. After doing so, switch on the taps to drain any water remaining in the system. The procedure of getting rid of the existing faucets can be fairly bothersome because of the limited gain access to that is commonly the situation.
Utilize a basin wrench (crowsfoot spanner) or a faucet device to reverse the nut that attaches the supply pipelines to the faucets. Have a towel all set for the continuing to be water that will certainly originate from the pipelines. As soon as the supply pipelines have actually been eliminated, use the same tool to loosen the nut that holds the taps onto the bath/basin. You will need to stop the solitary faucets from transforming throughout this procedure. When the faucets have been removed, the holes in the bath/basin will need to be cleaned of any old sealing compound.
Before moving on to fit the new taps, compare the pipe connections on the old faucets to the brand-new faucets. If the old faucets are longer than the brand-new faucets, then a shank adapter is required for the new taps to fit.
Fitting New Taps
If the tails of the new taps are plastic, then you will need a plastic adapter to stop damages to the string. One end of the adapter fits on the plastic tail of the faucet and also the various other end supplies a link to the existing supply pipelines.
If you need to fit a monobloc, then you will certainly require reducing couplers, which connects the 10mm pipe of the monobloc to the basic 15mm supply pipe.
Next, position the tap in the mounting hole in the bath/basin guaranteeing that the washers are in place in between the faucet and also the sink. Safeguard the faucet in position with the maker supplied backnut. When the tap is safely in place, the supply pipes can be connected to the tails of the taps. The taps can either be attached by utilizing corrugated copper piping or with regular faucet ports. The former type should be attached to the faucet finishes initially, tightening only by hand. The supply pipes can later be attached to the various other end. Tighten up both ends with a spanner after both ends have been connected.
Installing the Bath tub
Making use of both wooden boards under its feet, place the bath tub in the called for setting. The wooden boards are valuable in equally spreading out the weight of the bath tub over the location of the boards rather than concentrating all the weight onto four little points.
The next goal is to ensure that the bath tub is leveled all round. This can be attained by inspecting the spirit level and adjusting the feet on the bathtub till the level checks out level.
To install faucets, fit all-time low of the furthest versatile tap connector to the ideal supply pipe by making a compression join; after that do the very same for the various other tap.
Switch on the water supply and also examine all joints as well as new pipework for leaks and also tighten them if needed. Fill up the tub and additionally examine the overflow outlet and the regular electrical outlet for leaks.
Finally, deal with the bathroom paneling as described in the manufacturer's user's manual. Tiling and also securing around the bath tub must wait until the bath tub has actually been used at the very least once as this will resolve it into its last setting.
Preparing for the Installment
First of all, the supporting structure supplied with the bathroom must be fitted (if required) according to the supplier's instructions. Next off, fit the taps or mixer to the bath tub. When suitable the tap block, it is very important to ensure that if the faucet includes a plastic washer, it is fitted in between the bath and also the taps. On a plastic bathroom, it is likewise reasonable to fit a supporting plate under the taps system to stop stress on the bath tub.
Fit the flexible tap adapters to the bottom of the two faucets making use of 2 nuts and olives (often supplied with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet opening, and afterwards pass the outlet with the hole in the bath. Utilize the nut provided by the producer to fit the plug-hole. Take a look at the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next, fit the end of the versatile overflow pipeline to the overflow outlet. After that, screw the pipeline to the overflow face which need to be fitted inside the bath. Make certain you make use of all of the supplied washing machines.
Attach the catch to the bottom of the waste outlet on the tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the trap to the electrical outlet. Attach all-time low of the overflow tube in a similar manner.The bath must currently prepare to be fitted in its final setting.
Tiling Around the Tub
In the location where the bathroom meets the tile, it is needed to secure the accompanies a silicone rubber caulking. This is essential as the installation can relocate sufficient to split a stiff seal, triggering the water to permeate the wall surface in between the bath and the tiling, resulting in problems with dampness and feasible leaks to the ceiling below.
You can choose from a variety of coloured sealants to blend in your fixtures and fittings. They are sold in tubes and cartridges, as well as are capable of sealing gaps up to a size of 3mm (1/8 inch). If you have a bigger space to fill up, you can fill it with twists of soaked newspaper or soft rope. Remember to always fill the bathtub with water before securing, to permit the activity experienced when the bathtub remains in usage. The sealant can crack fairly early if you do not take into account this movement prior to securing.
Conversely, ceramic coving or quadrant ceramic tiles can be utilized to edge the bath or shower tray. Plastic strips of coving, which are easy to use and reduce to dimension, are additionally quickly offered on the market. It is recommended to fit the tiles using waterproof or water-proof sticky as well as grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
Hopefully you liked our post on Installing A Bathtub. Thank you for taking a few minutes to read our content. Are you aware of another individual who is inquisitive about How to Install a Bathtub Yourself? Take a moment to share it. We appreciate reading our article about A Step-by-Step Guide to Installing a Bathtub.
Set An Appointment
Report this page